Furnace Repair in Greensburg, IN

First, make sure your thermostat is telling your furnace to start.

Change the batteries if the screen is blank. If the digital screen is jumbled, the thermostat may need to be replaced.

Make sure the switch is set to “heat” instead of “off” or “cool.”

Ensure the program is set to the appropriate day and time and is set to “run.” If you’re having a hard time overriding the program, set the temperature by using the up/down arrows and press the “hold” button. This will cause the furnace to start if thermostat programming is causing trouble.

Increase the temperature setting to 5 degrees warmer than the room temperature.

If your furnace hasn’t kicked on within few minutes, make sure it has power by toggling the fan switch from “auto” to “on.” If the fan doesn’t start, your furnace might not have power.

If you have a smart thermostat—like one made by Nest, Ecobee, Lux, Honeywell or Bosch—troubleshooting is very model-specific. Refer to the manufacturer’s website for help. If you still can’t get your Wi-Fi thermostat to work, call us at 812-663-7252 for heating and cooling service.

Next, you will need to check if your breaker and furnace switch are on.

Locate your house’s main electrical panel. If you have no idea where it is, keep an eye out for a gray metal box in your basement, garage or closet.

Make sure your hands and feet are dry before touching the panel or breakers.

Look for the breaker labeled “furnace” or “heat,” and make sure it’s switched “on.” If the breaker has tripped, it will be in the middle or “off” position.

Using one hand, firmly switch the breaker to the “on” position. If the breaker immediately trips and pops back to “off,” leave it alone and call a professional from Wallpe Heating & Cooling at 812-663-7252 right away.

No matter your furnace’s age or brand, it has at least one standard wall switch located on or by it.

Make sure the switch is flipped up in the “on” position. If it was turned off, it could take your furnace up to five minutes to start. (If you don’t know where to find your furnace, look in your basement, garage or utility closet. It could also be in a crawl space or attic.)

When it comes to furnace problems, a grungy, clogged air filter is frequently to blame.

If your filter is too dirty:

• Your furnace won’t stay on, or it could overheat from restricted airflow.
• Your energy bills could be higher because your furnace is turning on more than it should.
• Your furnace could break down too soon because a dirty filter causes it to overwork.
• Your furnace can be disconnected from power if an extremely dirty filter causes the breaker to trip.

Depending on what type of furnace you own, your air filter will be inside the blower compartment of your furnace, an attached filter case or wall-mounted return air grille.

To replace your filter:

1. Turn off your furnace.
2. Take out the filter and angle it toward the light. If you can’t see light through it, use a new one.
3. Insert the new filter with the arrow pointing toward the furnace to avoid damage.

Flat filters should be replaced every month, while pleated filters should last about three months. You can also use a washable filter that will last about 10 years. If you have children or pets, you may have to change your filter sooner.

To make the process easier in the future, use a permanent marker on your furnace housing or ductwork to list the airflow direction and filter size.

Otherwise known as drain pans, condensate pans catch water your furnace draws from the air.

If water is leaking out of your furnace or its pan has standing water in it, follow these steps.

• If your pan has a drain (look for a PVC pipe), check that it isn’t full. If it needs to be drained, use a special pan-cleaning tablet you can get at home improvement or hardware stores.
• If your pan has a pump, inspect the float switch. If the switch is stuck “up” with water in the pan, contact us at 812-663-7252, because you will likely need a new pump.

If malfunctions persist, look inside your furnace’s plastic window to verify the status of the blower motor. Depending on the model, the light could also be fixed on the outside of your furnace.

If you see anything else besides a steady, colored light or blinking green light, call us at 812-663-7252 for HVAC service. Your furnace may be giving an error code that needs professional help.

If your furnace tries to start but turns off without distributing heat, a dirty flame sensor could be responsible. When this occurs, your furnace will attempt to ignite three times before a safety feature turns it off for about an hour.

If you feel comfortable with opening up your furnace, cleaning your flame sensor is something you can do by yourself. Or, one of our heating service professionals can do it for you.

If you want to clean the sensor yourself, you’ll need:

• A 1/4” hex screwdriver or wrench
• Piece of light grit sandpaper, steel wool or emery cloth
• A dry, clean paper towel

Next:

• Turn off the furnace’s power by using its wall switch or breaker. If your gas valve is not electric, you will need to shut off the gas as well.
• Take off the furnace’s front panel and trace the wire to the flame sensor.
• Unscrew the rod and use your sandpaper, steel wool or emery cloth to lightly rub the metal rod.
• Wipe off the rod with a paper towel.
• Remount the sensor.
• Replace the furnace doors.
• Turn the furnace’s power back on. It may go through a series of checks before resuming regular operation. If your furnace doesn’t start, the sensor may need to be replaced or something else might be wrong. If this happens, call us at 812-663-7252 for heating and cooling repair assistance.

If you own an older furnace, the pilot light could be turned off. To relight it, find the instructions on a label on your furnace, or follow these steps.

• Look for the switch on the bottom of your furnace labeled “pilot,” “on” and “off.”
• Turn the switch to the “off” position.
• Wait at least five minutes to avoid possibly sparking a fire.
• Turn the knob to “pilot.”
• Hold down the “reset” button as you bring the flame of a long lighter to the pilot light opening.
• Release the “reset” button once the pilot light is lit.

If you have followed the instructions twice and the pilot light still won’t light or stay lit, contact us at 812-663-7252 for furnace service.

Try switching on another gas appliance. If it doesn’t work, your natural gas service could be turned off, or you could be out of propane.